国产在线一区二区三区,夜夜笙精品麻豆7777,久久久久久91香蕉国产,蜜桃91丨九色丨蝌蚪91桃色
Welcome to Changzhou yuen machinery equipment co. LTD!
Hot Keywords:     Automatic single end terminal    Ultra static terminal    Strip and strip punch
NewsNEW CENTER
CONTACT USCONTACT US

Conatct:Mr Wu

Mobile:+Q:2223857802

Tel:+Q:2223857802

E-mail:898063083@qq.com

Add:4-2026, yikang electromechanical plaza, tianning district, changzhou city

NewsYour current location: Home > News
Common failures and solutions of computer stripper
Release:2018-01-14Browse 1396 
Details

The thread of the computer stripper cannot be peeled off

1. Check the cutting depth of the line, and adjust the line diameter value to decrease.

2. The clearance of the feed line transmission wheel is too large, and the clearance of the feed line transmission wheel is adjusted.

3. Whether the head stripping setting is greater than 2mm.

4. Stolen goods are in the pipeline.

5. The setting of return knife is too large, so it needs to be reduced.

The tail of a wire stripper cannot be peeled off

1. Check the cutting depth of the line, and adjust the line diameter value to decrease.

2. The clearance of outgoing transmission wheel is too large, and the clearance of outgoing transmission wheel is reduced.

3. Whether the head stripping setting is greater than 2mm.

4. The setting of return knife is too large, so it needs to be adjusted down.

Line skin crushed

1. Adjust the gap between the incoming transmission wheel and the outgoing transmission wheel.

2. Contact the factory and replace the transmission wheel.

Core cut out

1. Adjust the wire diameter to the appropriate degree (the best position is when the blade is just cut through the wire but the wire core is not damaged).

2. If the wire skin is very thin, after adjusting the wire diameter, it is found that it cannot be peeled, the return value can be appropriately reduced.

The length of the actual line varies, and the actual line grows at or equal to the set line length

1. The clearance of the incoming line transmission wheel is too large, and sometimes the wire head cannot be peeled off. The unopened line of the wire head is larger than the set line length, and the "incoming line clearance adjustment wheel" can be adjusted to increase the pressure.

2. Please check and properly clean the stolen goods in the wire tube.

3. Adjust the pressure of the incoming line transmission wheel.

The actual line length is less than or equal to the set line length

1. The wire itself is of different thickness.

2. The roller has stolen goods, which need to be cleaned. There is wax on the wire surface, causing the inlet and outlet transmission wheel to slip.

3. Take out the line, set the program as "00", run it empty, stop it, and check whether the "in and out line wheel" turns flexibly or is stuck.

4. There is a lag in the wire release frame, which causes the input line to slip.

Part of the core is too long

1. The wire diameter is too small, and the cutting edge is cut into the wire core.

2. The setting of returning knife is too small, and the parameters of returning knife should be appropriately increased.

Sometimes the wires are connected without being cut off

1. Add oil to the moving part of the knife edge and try again (generally refuel every 8 hours).

Slow down and try again.

3. Check whether the wire specification is within the allowable range of this model.

4. Does the blade become blunt?

The cut is tilted at a tangent

1. The wire itself is too bent and needs straightening.

2. The wire mouth is not directly opposite the center of the tool mouth.


Link: 常州360推廣
  Copyright  Changzhou yuen machinery equipment co. LTD  All Rights Reserved  【Login】
TopQQMegWechatBottom
QQ
點(diǎn)擊這里給我發(fā)消息
QQ
點(diǎn)擊這里給我發(fā)消息
Welcome to leave a messageClose
Contact:
Tel:
  
WeChat, scan, plus attentionClose
国产在线一区二区三区,夜夜笙精品麻豆7777,久久久久久91香蕉国产,蜜桃91丨九色丨蝌蚪91桃色